In the CUT&RUN protocol, the addition of digitonin to the buffers facilitates the permeabilization of cell membranes and entry of the primary antibody and pAG-MNase enzyme into the cells and nuclei. Therefore, having an adequate amount of digitonin in the buffers is critical to the success of antibody and enzyme binding and digestion of targeted genomic loci. Different cell lines show differing sensitivities to digitonin cell permeabilization. While the amount of digitonin recommended in this protocol should be sufficient for permeabilization of most cell lines, we recommend an initial test of your specific cell line. We have found that the addition of excess digitonin is not deleterious to the assay, so there is no need to perform a concentration curve. Rather, a quick test to determine if the recommended amount of digitonin works for your cell line is sufficient.
NOTE: Digitonin Solution should be stored at -20°C. Please keep on ice during use and store at -20°C when finished for the day.
Sonication of the input DNA sample is recommended because only fragmented genomic DNA (<10 kb) can be purified using DNA purification spin columns. Additionally, the fragmented genomic DNA (<1kb) may be used as the negative control in NG-seq analysis. Sonication should be optimized so that the input DNA is 100-600 bp in length.
We recommend using the input sample for NG-seq because it provides a convenient and unbiased representation of the cell genome. While the IgG sample can also be used as a negative control for NG-seq, it may show enrichment of specific regions of the genome due to non-specific binding. Unfragmented input DNA can be used for qPCR analysis. However, unfragmented DNA must be purified using phenol/chloroform extraction followed by ethanol precipitation.
! All buffer volumes should be increased proportionally based on the number of input samples being prepared.
NOTE: Samples will be incubated at 55°C in Step 9, so it is recommended to use a safe-lock 1.5 ml tube to reduce evaporation during the incubation.
|1. Concanavalin A beads clump during the experiment.||Bead clumping is normal and is not usually deleterious to the assay.||Resuspend clumped beads by gently pipetting up and down.|
|Room temperature incubation of beads and cells is too long.||Activate Concanavalin A beads at 4°C and incubate with cells no longer than 5 min (Section I, Step 14).|
|Cells are lysing during preparation.||Be sure to prepare cells at room temperature and as quickly as possible to minimize cell stress (Section I, Steps 7-16).|
|Digitonin concentration may be too high.||Some cells may be more sensitive to digitonin and lyse at higher concentrations. Reduce the amount of digitonin in the assay, but be sure to confirm the amount used is sufficient for cell permeabilization (see APPENDIX A).|
|2. No DNA is detected in the purified DNA samples using a picogreen-based DNA quantification assay.||This is typical when starting with low cell numbers (<10,000 cells), but DNA should be detectable when starting with the recommended 100,000 cells.||Be sure to use a picogreen-based DNA quantification assay. Purified DNA is not typically detectable using a NanoDrop, Bioanalyzer® or Tapestation®.|
|Cell count is off, cells are lost or lysing during preparation.||Starting cell culture should be 60-90% confluent and look healthy (> 90% live cells).|
|Be sure to prepare cells at room temperature and as quickly as possible to minimize cell stress.|
|Wash all cells in one vial to minimize cell loss (Section I, Steps 7-16).|
|Digitonin is not effectively permeabilizing the cells.||Be sure to store Digitonin Solution at -20°C when not in use, as it is unstable when stored above -20°C.|
|Be sure to test and confirm that the amount of digitonin used is sufficient to permeabilize your specific cell line (see APPENDIX A).|
|pAG-MNase enzyme is not working properly in the assay.||The pAG-MNase is highly stable and should maintain activity for a long time when stored properly.|
|The pAG-MNase requires Ca2+ divalent cations for activity. Be sure to add calcium chloride for activation of the enzyme (Section III, Step 8).|
|Be sure to digest for 30 min to allow the enzyme to sufficiently digest the chromatin (Section III, Step 9).|
|Not enough antibody is added to the reaction or antibody does not work in the CUT&RUN assay.||Not all antibodies work in CUT&RUN. If possible, use a CUT&RUN validated antibody. Alternatively, some ChIP- and IF-validated antibodies also work for CUT&RUN.|
|Be sure to include the positive control Tri-Methyl-Histone H3 (Lys4) (C42D8) Rabbit mAb to show your assay is working.|
|3. No signal in qPCR or NG-seq analysis.||See possible causes for problem #2.||See recommendations problem #2.|
|Not enough DNA added to the qPCR reaction.||Add more DNA to the PCR reaction or increase the number of amplification cycles.|
|Not enough DNA added to the NG-seq DNA library preparation.||Be sure to quantify the purified DNA using a picogreen-based DNA quantification assay and use the recommended amount of starting DNA and PCR-amplification cycles (see Section VII).|
|PCR-amplified region may span a nucleosome-free region.||DNA fragments generated in the CUT&RUN assay are typically smaller than DNA fragments generated in the ChIP assay. Therefore, it is critical to design primers to generate amplicons no longer than 60 to 80 bp.|
|4. High background signal in qPCR or NG-seq analysis.||Genomic DNA has become highly fragmented due to harsh treatment of samples.||Always use the Rabbit (DA1E) mAb IgG XP® Isotype Control (CUT&RUN) #66362 negative control antibody to determine background signal in the CUT&RUN assay.|
|To minimize DNA fragmentation, avoid vigorous vortexing and introduction of bubbles during resuspension of cells.|
|Genomic DNA has become highly fragmented due to cell stress and lysis.||Be sure to prepare cells at room temperature and as quickly as possible to minimize cell stress. Wash all cells in one vial to minimize cell loss (Section I, Steps 7-16).|
|Digestion is not performed at 0°C and chromatin is over-digested.||Digestion should be performed in an ice-water bath. Digestion at higher temperatures can significantly increase background signal.|
|Make sure to pre-cool cell samples and calcium chloride in an ice-water bath for 5 min prior to adding the calcium chloride and initiating the digest. Quickly mix the samples and place back in the ice-water bath.|
|Large non-specific genomic DNA can also diffuse into the supernatant and contaminate the smaller fragments released by targeted digestion.||Do not incubate samples at 37°C for > 10 min and do not shake samples during incubation (Section III, Step 11). Ten minutes is sufficient for diffusion of digested fragments into the supernatant.|
|Large genomic DNA fragments can be removed by size-selection using AMPure® XP Beads or SPRIselect® Reagent Kit prior to qPCR analysis.|
|For NG-seq analysis, shorten the PCR amplification time (10-15 sec) during library construction to exclude amplification of large DNA fragments.|
|Too much antibody is used in the assay, resulting in non-specific binding and digestion.||If possible, be sure to use a CUT&RUN validated antibody at the recommended dilution. If not, ChIP-validated and IF-validated antibodies often work at their ChIP- and IF-recommended dilutions. You may need to titrate your antibody in the assay.|