Western blot analysis of extracts from HeLa, THP-1, and YB2/0 cell lines using Caspase-8 (D35G2) Rabbit mAb.
Western blot analysis of extracts from control HeLa cells (lane 1) or Caspase-8 knockout HeLa cells (lane 2) using Caspase-8 (D35G2) Rabbit mAb #4790 (upper), or β-actin (13E5) Rabbit mAb #4970 (lower). The absence of signal in the Caspase-8-knockout HeLa cells confirms specificity of the antibody for Caspase-8.
Western blot analysis of extracts from CTLL-2 cells, untreated (-) or treated with Cycloheximide #2112 (CHX, 10 μg/ml, overnight) followed by Human Tumor Necrosis Factor-α (hTNF-α) #8902 (20 ng/ml, 4 hr; +), using Caspase-8 (D35G2) Rabbit mAb.
Western blot analysis of 293T cells, mock transfected (-) or transfected with a construct expressing Myc/DDK-tagged full-length human Caspase-8 protein (hCasp8-Myc/DDK; +), full-length mouse Caspase-8 protein (mCasp8; +), or full-length human Caspase-10 protein (hCasp10; +), using Caspase-8 (D35G2) Rabbit mAb.
|REACTIVITY||H M R|
|MW (kDa)||10, 57|
Supplied in 10 mM sodium HEPES (pH 7.5), 150 mM NaCl, 100 µg/ml BSA, 50% glycerol and less than 0.02% sodium azide. Store at –20°C. Do not aliquot the antibody.
For western blots, incubate membrane with diluted primary antibody in 5% w/v BSA, 1X TBS, 0.1% Tween® 20 at 4°C with gentle shaking, overnight.
NOTE: Please refer to primary antibody product webpage for recommended antibody dilution.
From sample preparation to detection, the reagents you need for your Western Blot are now in one convenient kit: #12957 Western Blotting Application Solutions Kit
NOTE: Prepare solutions with reverse osmosis deionized (RODI) or equivalent grade water.
Load 20 µl onto SDS-PAGE gel (10 cm x 10 cm).
NOTE: Volumes are for 10 cm x 10 cm (100 cm2) of membrane; for different sized membranes, adjust volumes accordingly.
* Avoid repeated exposure to skin.
posted June 2005
revised June 2020
Protocol Id: 10
Caspase-8 (D35G2) Rabbit mAb detects endogenous levels of total caspase-8, including the p10 subunit of the activated protein. Caspase-8 (D35G2) Rabbit mAb may also cross-react with overexpressed levels of caspase-10.
Human, Mouse, Rat
Monoclonal antibody is produced by immunizing animals with a synthetic peptide corresponding to residues near the carboxyl terminus of human caspase-8 protein.
Apoptosis induced through the CD95 receptor (Fas/APO-1) and tumor necrosis factor receptor 1 (TNFR1) activates caspase-8 and leads to the release of the caspase-8 active fragments, p18 and p10 (1-3). Activated caspase-8 cleaves and activates downstream effector caspases such as caspase-1, -3, -6, and -7. Caspase-3 ultimately elicits the morphological hallmarks of apoptosis, including DNA fragmentation and cell shrinkage.
Explore pathways + proteins related to this product.
Except as otherwise expressly agreed in a writing signed by a legally authorized representative of CST, the following terms apply to Products provided by CST, its affiliates or its distributors. Any Customer's terms and conditions that are in addition to, or different from, those contained herein, unless separately accepted in writing by a legally authorized representative of CST, are rejected and are of no force or effect.
Products are labeled with For Research Use Only or a similar labeling statement and have not been approved, cleared, or licensed by the FDA or other regulatory foreign or domestic entity, for any purpose. Customer shall not use any Product for any diagnostic or therapeutic purpose, or otherwise in any manner that conflicts with its labeling statement. Products sold or licensed by CST are provided for Customer as the end-user and solely for research and development uses. Any use of Product for diagnostic, prophylactic or therapeutic purposes, or any purchase of Product for resale (alone or as a component) or other commercial purpose, requires a separate license from CST. Customer shall (a) not sell, license, loan, donate or otherwise transfer or make available any Product to any third party, whether alone or in combination with other materials, or use the Products to manufacture any commercial products, (b) not copy, modify, reverse engineer, decompile, disassemble or otherwise attempt to discover the underlying structure or technology of the Products, or use the Products for the purpose of developing any products or services that would compete with CST's products or services, (c) not alter or remove from the Products any trademarks, trade names, logos, patent or copyright notices or markings, (d) use the Products solely in accordance with CST's Product Terms of Sale and any applicable documentation, and (e) comply with any license, terms of service or similar agreement with respect to any third party products or services used by Customer in connection with the Products.